Did you purchase a high amp alternator from those other guy's and didn't come with an overdrive pulley?
Replace your slow turning alternator with an OVERDRIVE pulley. Increase the amperage and reduce voltage drop and headlight dimming when idling.
Serpentine pulley size is measured from top of grooves and not outer rim. Minimal V-pulley size is achieved by thickness of belt used.
$26.95
2.3 INCH SINGLE V-BELT OVERDRIVE PULLEY (FACTORY 2.6") ITEM# 24-1109
Used on standard General Motors and Ford alternators with single 3/8" or 10mm V-Belt. Can be used on Industrial / Commercial applications with 13mm belt.
Note: 2.3" diameter achieved when using a 3/8" or 10mm belt width.
Increases rotor speed at idle by over 400 RPM's for higher output.
Dimensions- (3/8" or 10mm - 13mm) V-Belt x 2.6" (66mm) overall OD x .67 (17mm) Bore w/key way
Features:
* Machined from cold rolled steel
$19.95
2.6 INCH SINGLE V-BELT PULLEY ITEM# 32-1002C
Used on standard General Motors and Ford alternators with single 3/8" V-Belt. Dress up engine compartment with a new look.
Dimensions- 3/8" (10mm) V-Belt x 2.6" (66mm) OD x .67 (17mm) Bore
Features:
* Machined from cold rolled steel with chrome finish
$ 36.95
1.7 INCH 6 GROOVE OVERDRIVE PULLEY (FACTORY 2.21") ITEM# 32-8024
MOST POPULAR
Used on standard General Motors and Ford alternators with 6 groove serpentine belts.
Increases rotor speed at idle by over 800 RPM's for higher output.
Dimensions- (21mm) Belt x 1.7" (44mm) OD x .67" (17mm) Bore Spacer washers included
Features:
* Machined from cold rolled steel. * Anodized finish
$26.95
1.9 INCH 6 GROOVE OVERDRIVE PULLEY (FACTORY 2.6") ITEM# 32-6005
Used on standard General Motors and Ford alternators with 6 groove serpentine belts.
Increases rotor speed at idle by over 800 RPM's for higher output.
Dimensions- (21mm) Belt x 1.9" (49mm) OD x .67" (17mm) Bore
Features:
* Machined from cold rolled steel. * Anodized finish
$26.90
2.48" SINGLE V BELT PULLEY ITEM# 24-7100
Used on standard agricultural, industrial, marine alternators.
Dimensions-(16-19mm) Belt x 63mm OD x (17mm) Bore
Note: Conversion pulley with small OD to increase rotor, RPM at slow engine speeds. Includes Hex nut.
$46.95
1.9 INCH 8 GROOVE OVERDRIVE PULLEY (FACTORY 2.6") ITEM# 233940
Used on standard 3G, 6G Ford alternators and various applications with 8 groove serpentine belts.
Increases rotor speed at idle by over 800 RPM's for higher output.
Dimensions- (28mm) Belt x 1.9" (49mm) OD x .67" (17mm) Bore Spacer washers included Features:
* Machined from cold rolled steel. * Black finish
Note: Ball bearing must be clearily visible when removing pulley from existing alternator. Some 3G alternators have raised lip casings under the pulley which needs to be cut off for proper installation.
$36.95
2.1 INCH 8 GROOVE OVERDRIVE PULLEY (FACTORY 2.6") ITEM# 32-7304
Used on standard 3G, 6G Ford alternators and various applications with 8 groove serpentine belts.
Increases rotor speed at idle by over 600 RPM's for higher output.
Dimensions- (28mm) Belt x 2.1" (53mm) OD x .67" (17mm) Bore
Features:
* Machined from cold rolled steel. * Anodized finish
Note: Ball bearing must be clearily visible when removing pulley from existing alternator. Some 3G alternators have raised lip casings under the pulley which needs to be cut off for proper installation.
HONDA - TOYOTA - ACURA
$36.95
1.9 INCH 5 GROOVE OVERDRIVE PULLEY (FACTORY 2.6") ITEM# 234020
Used on standard Nippondenso alternators with 5 groove serpentine belts.
Increases rotor speed at idle by over 800 RPM's for higher output.
Dimensions- (18mm) Belt x 1.9" (48mm) OD x .67" (17mm) Bore
Features:
* Machined from cold rolled steel. * Black finish
$26.95
1.9 INCH 4 GROOVE OVERDRIVE PULLEY (FACTORY 2.5") ITEM# 24-82264
Used on standard Nippondenso alternators with 4 groove serpentine belts.
Increases rotor speed at idle by over 800 RPM's for higher output.
Dimensions- (14mm) Belt x 1.9" (48mm) OD x .59" (15mm) Bore
Features:
* Machined from cold rolled steel. * Anodized finish
